BELL RS7 HELMET SA2020 BELL RS7 HELMET SA2020 BELL Based on the HP7 design and featuring a lightweight carbon composite shell using Bell’s high-pressure proprietary molding system, the RS7 uses and innovative shell and shield design to improve acoustic comfort, aerodynamic performance and energy absorbing capabilities. The sleek, modern design features an advanced ventilation system with 14 air-intake and extraction channels that can be used with or without air-intake covers (available separately). The RS7 double screen anti-fog (DSAF) visor and rubber gasket seal ensured air, water and dust will not enter the eyeport.        Lightweight carbon composite shell Advanced multi-density, multi piece liner to maximize energy absorption and impact performance Optical grade injection molded Double Screen Anti-Fog (DSAF) visor for anti-fog control and superior visibility Powerful and effective top and chin bar ventilation system with 14 air intake and extraction channels for maximum ventilation  Shell and shield design optimized to improve aerodynamic performance, reduce internal noise and enhance energy management capacities Integrated channels in face piece offer multiple options to install drink tube and radio systems Air Intake, side air extractors, rear spoiler, top and chin bar gurneys available separately Top air attachments available separately for use with external cooling systems Factory installed Hans posts as original equipment Synthetic rubber gasket seal to prevent dirt and water from entering the helmet Shield and pivot kit: SE07, SV(SE07) Homologation: Snell SA2020 and FIA8859-2020 approved Colors: white & matte black Graphics: falcon blue and falcon red Sizes: 6 3/4 (54) to 7 5/8+ (61+) Proper helmet fit is vital to the performance of a helmet during an impact. For maximum protection the helmet must fit properly with the chin strap securely fastened and provide adequate peripheral vision. Measuring the head is only a starting point for the entire sizing procedure. Due to varying shapes, heads that are apparently the same size when measured by a tape may not necessarily fit the same size helmet. A small metal tape measure or a cloth tape may be used to make your initial measurement. You can also use a string, which can then be laid against a measuring tape. The circumference of the head should be measured at a point approximately one inch above the eyebrows in front, and at a point in the back of the head that results in the largest possible measurement. Take several measurements. The largest measurement is the one you want to try on first. If you use a balaclava or head sock, always measure and fit the helmet with it on. Use the Bell sizing chart to determine the size that best matches the head measurement.   

BELL RS7 HELMET SA2020

Code: 1310A01
$899.95
In Stock
  • 1-4 DAYS DELIVERY

  • 100% ORIGINAL AND QUALITY

Based on the HP7 design and featuring a lightweight carbon composite shell using Bell’s high-pressure proprietary molding system, the RS7 uses and innovative shell and shield design to improve acoustic comfort, aerodynamic performance and energy absorbing capabilities. The sleek, modern design features an advanced ventilation system with 14 air-intake and extraction channels that can be used with or without air-intake covers (available separately). The RS7 double screen anti-fog (DSAF) visor and rubber gasket seal ensured air, water and dust will not enter the eyeport.

      

  • Lightweight carbon composite shell
  • Advanced multi-density, multi piece liner to maximize energy absorption and impact performance
  • Optical grade injection molded Double Screen Anti-Fog (DSAF) visor for anti-fog control and superior visibility
  • Powerful and effective top and chin bar ventilation system with 14 air intake and extraction channels for maximum ventilation 
  • Shell and shield design optimized to improve aerodynamic performance, reduce internal noise and enhance energy management capacities
  • Integrated channels in face piece offer multiple options to install drink tube and radio systems
  • Air Intake, side air extractors, rear spoiler, top and chin bar gurneys available separately
  • Top air attachments available separately for use with external cooling systems
  • Factory installed Hans posts as original equipment
  • Synthetic rubber gasket seal to prevent dirt and water from entering the helmet
  • Shield and pivot kit: SE07, SV(SE07)
  • Homologation: Snell SA2020 and FIA8859-2020 approved
  • Colors: white & matte black
  • Graphics: falcon blue and falcon red
  • Sizes: 6 3/4 (54) to 7 5/8+ (61+)

Proper helmet fit is vital to the performance of a helmet during an impact. For maximum protection the helmet must fit properly with the chin strap securely fastened and provide adequate peripheral vision.

Measuring the head is only a starting point for the entire sizing procedure. Due to varying shapes, heads that are apparently the same size when measured by a tape may not necessarily fit the same size helmet.

A small metal tape measure or a cloth tape may be used to make your initial measurement. You can also use a string, which can then be laid against a measuring tape.

The circumference of the head should be measured at a point approximately one inch above the eyebrows in front, and at a point in the back of the head that results in the largest possible measurement. Take several measurements. The largest measurement is the one you want to try on first. If you use a balaclava or head sock, always measure and fit the helmet with it on. Use the Bell sizing chart to determine the size that best matches the head measurement. 

 

Based on the HP7 design and featuring a lightweight carbon composite shell using Bell’s high-pressure proprietary molding system, the RS7 uses and innovative shell and shield design to improve acoustic comfort, aerodynamic performance and energy absorbing capabilities. The sleek, modern design features an advanced ventilation system with 14 air-intake and extraction channels that can be used with or without air-intake covers (available separately). The RS7 double screen anti-fog (DSAF) visor and rubber gasket seal ensured air, water and dust will not enter the eyeport.

      

  • Lightweight carbon composite shell
  • Advanced multi-density, multi piece liner to maximize energy absorption and impact performance
  • Optical grade injection molded Double Screen Anti-Fog (DSAF) visor for anti-fog control and superior visibility
  • Powerful and effective top and chin bar ventilation system with 14 air intake and extraction channels for maximum ventilation 
  • Shell and shield design optimized to improve aerodynamic performance, reduce internal noise and enhance energy management capacities
  • Integrated channels in face piece offer multiple options to install drink tube and radio systems
  • Air Intake, side air extractors, rear spoiler, top and chin bar gurneys available separately
  • Top air attachments available separately for use with external cooling systems
  • Factory installed Hans posts as original equipment
  • Synthetic rubber gasket seal to prevent dirt and water from entering the helmet
  • Shield and pivot kit: SE07, SV(SE07)
  • Homologation: Snell SA2020 and FIA8859-2020 approved
  • Colors: white & matte black
  • Graphics: falcon blue and falcon red
  • Sizes: 6 3/4 (54) to 7 5/8+ (61+)

Proper helmet fit is vital to the performance of a helmet during an impact. For maximum protection the helmet must fit properly with the chin strap securely fastened and provide adequate peripheral vision.

Measuring the head is only a starting point for the entire sizing procedure. Due to varying shapes, heads that are apparently the same size when measured by a tape may not necessarily fit the same size helmet.

A small metal tape measure or a cloth tape may be used to make your initial measurement. You can also use a string, which can then be laid against a measuring tape.

The circumference of the head should be measured at a point approximately one inch above the eyebrows in front, and at a point in the back of the head that results in the largest possible measurement. Take several measurements. The largest measurement is the one you want to try on first. If you use a balaclava or head sock, always measure and fit the helmet with it on. Use the Bell sizing chart to determine the size that best matches the head measurement.